A CBM to kg calculator converts physical volume into chargeable weight. It uses freight billing ratios. For example, 1 m³ equals 166.67 kg for air cargo. It is 200 kg for express couriers. Also, it is 333.33 kg for road or rail groupage. For sea LCL freight, it is 1,000 kg. Carriers bill on the higher figure. This is either your cargo’s actual physical weight or the calculated volumetric weight.
A cubic meter of lightweight foam weighs much less than steel. Therefore, carriers cannot rely on physical mass alone to set prices. Transport vehicles have fixed cargo spaces. They also have maximum payload weight limits. To balance these constraints, freight networks convert cargo volume into a billable weight. They use standardized industry conversion ratios. You can use the tool below. It helps you test your shipment volume and density across transport modes.
Shipping density calculator
Runs in your browser; nothing you enter is sent anywhere. Carrier figures differ, so confirm the final numbers with your forwarder. Whole shipment: all-in-one freight calculator →
why you need a cbm to kg calculator
Volume measures spatial capacity. Weight measures physical mass. Materials vary in compactness. There is no universal CBM to kg conversion. A cbm to kg calculator needs cargo material density. Calculate this as density (kg/m³) = weight (kg) ÷ volume (m³).

Transport carriers manage two distinct physical constraints on every journey. They consider available floor space and volumetric capacity inside the container, trailer, or aircraft belly. In addition, they account for maximum allowable gross vehicle weight limits. For example, if a shipper loads a container full of light, bulky items like acoustic foam or pillows, the container becomes physically full. This happens long before it reaches its maximum payload weight capacity. Billing strictly by physical kilograms, even with a cbm to kg calculator, would mean a full container generates minimal revenue. It would also take up space that could have held other cargo.
To prevent loss of capacity value, cargo networks establish a billing ratio. This is a baseline density threshold. Here, volume and weight carry equal financial value. Carriers charge cargo with density below this baseline threshold based on its volumetric weight. However, they charge denser cargo based on its actual physical weight. For an in-depth breakdown of how cargo density affects pricing structures, see the shipping density guide.
What are the billing ratios for each transport mode?
| Mode | Common ratio | kg per m³ | lb per ft³ |
|---|---|---|---|
| Air cargo | 1:6000 cm³/kg | 166.67 | 10.4 |
| Express courier (DHL Express, FedEx metric, Parcelforce) | 1:5000 cm³/kg | 200 | 12.5 |
| Australia Post parcels | cubic weight factor | 250 | 15.6 |
| Rail (DHL Global Forwarding) | 1:3000 cm³/kg | 333.33 | 20.8 |
| European road groupage, international (DSV, DB Schenker) | 1 m³ = 333 kg | 333 | 20.8 |
| Ocean LCL (W/M) | 1 m³ = 1,000 kg | 1,000 | 62.4 |
The imperial values in the rightmost column divide the metric kg/m³ density figure by 16.0185, based on the standard physical conversion factor where 1,000 kg/m³ equals 62.43 lb/ft³. Specific regional and carrier rules apply across these modes for a cbm to kg calculator:

- Air cargo: The standard 1:6000 volumetric ratio equates to 166.67 kg per cubic meter. Air waybills often round this to 167 kg/m³. Maersk notes this as an industry standard. The International Air Transport Association (IATA) defines it. However, some specialized air freight quotes or charter services apply custom ratios. Therefore, check individual quote terms.
- Express courier networks: Global courier operators use specific ratios. For example, DHL Express, FedEx, and Parcelforce use them. FedEx uses metric pricing schedules. Parcelforce applies them for international zones 4 through 12. Canada Post Priority, Xpresspost, and Expedited services also apply. They use a 1:5000 ratio (200 kg/m³). However, Canada Post Regular Parcel services use a 1:6000 ratio. For shipments measured in inches, FedEx, UPS Daily Rates, and USPS apply a dimensional factor. This applies from July 12, 2026. The factor is 139 in³/lb. This converts to approximately 5,022 cm³/kg. Therefore, it is roughly 199 kg/m³.
- Road freight groupage: Standard European road transport groupage typically applies 333 kg per CBM. However, exact tariffs depend on the carrier network and transport route. For instance, DSV applies 333 kg/m³ on general international European lines. But they increase this to 360 kg/m³ for cargo moving into or out of the UK and Ireland. Also, they use 350 kg/m³ within Nordic countries. Furthermore, European road freight that cannot be stacked is often billed per loading meter. They do not bill it by simple volume. Review the loading meter calculator guide for non-stackable cargo logic.
- Ocean LCL freight: Less-than-container-load (LCL) ocean freight charges based on Weight/Measurement (W/M) revenue tons. This sets 1 m³ equal to 1,000 kg (1 metric ton). Because water weighs 1,000 kg/m³, ocean carriers only bill ocean cargo by physical weight if its density exceeds water. For full details on ocean freight rating structures, read how LCL sea freight is calculated.
How do you calculate chargeable weight step by step?
To calculate the billable weight for any consignment across any transport mode, follow these sequential steps:
- Measure exterior dimensions accurately: Measure the maximum length, width, and height. Do this for each packed item or pallet. Use centimeters (cm) or meters (m). Always measure from the extreme outer edges. For example, include box bulges and packaging straps. Also include corner edge protectors and wooden skid bases.
- Calculate total shipment CBM: You can multiply length × width × height. Do this for each carton or pallet. If you measure in meters, multiply L (m) × W (m) × H (m). This gives you the CBM directly. However, if you measure in centimeters, multiply L (cm) × W (cm) × H (cm). Then divide by 1,000,000. This converts the value to CBM. Finally, multiply by the total number of identical packages.
- Determine volumetric weight:
- Using density ratio: volumetric weight (kg) = CBM × mode ratio (kg/m³)
- Use a standard divisor: volumetric weight (kg) = total volume (cm³) ÷ divisor. For example, use 6,000 for air freight. Also, use 5,000 for express courier services.
- Weigh the complete consignment: Determine the total gross physical weight in kilograms. Use a scale for this measurement. Also, include pallets and strapping in the weight.
- Compare physical weight against volumetric weight: The chargeable weight is the higher value. This is between actual gross physical weight and calculated volumetric weight.
Both mathematical forms are equivalent. For example, dividing 1,000,000 cm³ (1 m³) by a standard air divisor of 6,000 cm³/kg yields 166.67 kg. Also, in a cbm to kg calculator, dividing 1,000,000 cm³ by a courier divisor of 5,000 gives 200 kg.
Worked example 1: a light, bulky shipment across five modes
For example, a consignment of outdoor seat cushions measures 2.4 m³. It weighs 380 kg. Therefore, its density is 380 ÷ 2.4 = 158.3 kg/m³.

| Mode | Volume-based figure | Actual | Charged on |
|---|---|---|---|
| Air (1:6000) | 2.4 × 166.67 = 400 kg | 380 kg | 400 kg |
| Courier (1:5000) | 2.4 × 200 = 480 kg | 380 kg | 480 kg |
| Rail (1:3000) | 2.4 × 1,000,000 ÷ 3,000 = 800 kg | 380 kg | 800 kg |
| Road, 333 kg/m³ | 2.4 × 333 = 799.2 kg | 380 kg | 799.2 kg |
| Sea LCL (W/M) | 2.4 W/M | 0.38 t | 2.4 W/M |
The 158.3 kg/m³ figure is below every table ratio. Carriers thus charge this cargo on volume. This applies to every mode. For example, consider sea freight. At 50 per revenue ton, the freight is 2.4 × 50 = 120. Replace this example rate with a real quote. Use a cbm to kg calculator for accuracy. Also, note that LCL minimums of about 1 W/M are typical.
Worked example 2: a dense shipment
For example, a crate of machine parts measures 1.2 m³. It weighs 900 kg. Therefore, its density is 900 ÷ 1.2 = 750 kg/m³.

- Air: 1.2 × 166.67 = 200 kg volumetric. Actual 900 kg is higher, so chargeable weight is 900 kg.
- Courier: 1.2 × 200 = 240 kg. Charged on 900 kg.
- Rail: 1.2 × 1,000,000 ÷ 3,000 = 400 kg. Charged on 900 kg.
- Road: 1.2 × 333 = 399.6 kg. Charged on 900 kg.
- Sea LCL: 1.2 m³ vs 900 ÷ 1,000 = 0.9 t. The larger is 1.2 W/M, so even this dense crate is billed on volume at sea.
You can easily overlook that last line. Sea freight has a very high 1,000 kg/m³ ratio. So, carriers only bill cargo denser than water on weight, a factor a cbm to kg calculator can help determine. This includes items such as metal, stone, or liquids in drums. Also, air vs sea freight covers the comparison between modes.
Worked example 3: a single parcel
Example: one carton of 50 × 40 × 35 cm weighing 9 kg.
- Volume: 0.5 × 0.4 × 0.35 = 0.07 m³
- DHL Express (5,000): 50 × 40 × 35 = 70,000 cm³; 70,000 ÷ 5,000 = 14 kg, so 14 kg is charged
- Australia Post (250 kg/m³): 0.07 × 250 = 17.5 kg, so 17.5 kg is charged
- Air cargo (6,000): 70,000 ÷ 6,000 = 11.67 kg, so 11.67 kg is charged
The same box costs a different billed weight with each carrier. Carrier-by-carrier rules are in the dimensional weight calculator guide.
How does shipping density determine which billing method applies?
Comparing cargo density directly against billing thresholds allows you to predict whether volume or weight will control your invoice:

- Below 166.67 kg/m³: Volume determines chargeable weight across all modes (air, courier, road, rail, and ocean LCL).
- Between 166.67 and 200 kg/m³: Air cargo bills on actual physical weight; courier, road, rail, and ocean LCL bill on volume.
- Next, Between 200 and 333 kg/m³: Air cargo and express couriers bill on actual weight; rail and road groupage bill on volume.
- Between 333 and 1,000 kg/m³: Air, courier, rail, and road groupage bill on actual physical weight. Ocean LCL, however, still bills on volume.
- Above 1,000 kg/m³: Actual weight determines billing across all modes, including ocean LCL.
These density bands offer a practical guide. However, carriers retain authority to apply line-haul minimums. They can also use pallet position rules or lane-specific tariff adjustments, which a cbm to kg calculator might help with.
What common mistakes lead to unexpected freight charges?
Miscalculating volumetric weight frequently causes unexpected carrier charges. Avoid these common mistakes:

- Treating 1 m³ as 1,000 kg for land or air transport: The 1 m³ = 1,000 kg conversion applies exclusively to ocean LCL freight. Applying this ratio to air or road freight undercalculates chargeable weight by 3 to 6 times.
- Using the air cargo ratio (6,000 divisor / 167 kg/m³) for express couriers: Express couriers use a 5,000 divisor (200 kg/m³). This applies to services like DHL, FedEx, and UPS. However, using the 6,000 air divisor understates true billable courier weight. It understates it by 20%.
- Measuring internal packaging dimensions: Volume calculations must reflect external shipping dimensions. Measuring inner dimensions ignores carton wall thickness, outer bulges, corner edge protectors, and wooden pallets. See how to calculate CBM to avoid measurement errors.
- Ignoring non-stackable loading space rules: Freight that cannot have other cargo stacked on top of it often triggers floor-space billing based on loading meters rather than pure cubic volume. Review the loading meter calculator guide to calculate charges for non-stackable pallets.
- Forgetting carrier minimum billing thresholds: Ocean LCL shipments generally carry a 1 CBM / 1 W/M minimum freight charge. Carriers will still bill shipping 0.3 CBM by sea at the 1 CBM minimum rate. Details on ocean freight rating logic are available in how LCL sea freight is calculated.
FAQ
How many kg is 1 CBM?
Physically, 1 CBM equals a different mass. This depends entirely on the cargo’s material density. For billing, 1 m³ translates to 166.67 kg for air freight. It is 200 kg for express couriers. Furthermore, it is 333.33 kg for road or rail groupage. For ocean LCL shipping, it is 1,000 kg.
What is the CBM to kg air freight ratio?
Air freight standardly uses a 1:6000 volumetric ratio, which means 1 m³ equals 166.67 kg (often rounded to 167 kg). IATA establishes this factor as an international aviation industry standard.
How does CBM to kg ocean freight pricing work?
Carriers rate ocean LCL freight on a Weight/Measurement (W/M) basis. Here, 1 CBM equals 1,000 kg (1 metric ton). The carrier calculates total volume in CBM. They also calculate total physical weight in metric tons. As a result, they bill for whichever numerical total is greater, often aided by a cbm to kg calculator.
How is kg converted to CBM?
To convert physical kilograms to volume, divide cargo mass by its known density in kg/m³. For example, 900 kg of cargo with a density of 750 kg/m³ occupies 900 ÷ 750 = 1.2 CBM of volume.
Does the same ratio apply in pounds and cubic feet?
Yes, billing ratios convert directly between metric and imperial systems. For example, an air cargo ratio of 166.67 kg/m³ equals 10.4 lb/ft³. The ocean freight ratio of 1,000 kg/m³ equals 62.43 lb/ft³, which a cbm to kg calculator can confirm.
Related guides
- Air Cargo Density: When You Pay for Weight vs Volume (1:6000)
- Furniture CBM Calculator: How to Estimate Volume for Furniture and Household Moves
- Pallet CBM Calculator: How to Calculate the CBM of a Pallet
- CBM Calculator in Inches: How to Calculate CBM from Inches
Sources and further reading
- DHL Global Forwarding: Calculating Chargeable Weight: air 1:6,000, sea 1:1,000 and rail 1:3,000 ratios.
- SEKO Logistics: LCL Shipping: 1 CBM = 1,000 kg revenue ton.
- DB Schenker: Transport Conditions, Land (PDF): kg per loading meter and per pallet place.
